Good Day, I flashed my NanoBridge M5 with 3.15.1.0 but according to this it is being reported as a Bullet M, ch.179 is not available which is what we are using for our mesh. The question is should I flash it with the Bullet M firmware ? Thanks Rich, W6ABJ node: W6ABJ-NB5-Q-1 model: Ubiquiti Bullet M !!!! UNSUPPORTED DEVICE !!!! boardid: 0xe235 Device has not been tested. Please file a ticket with your experiences. eth0 00:15:6D:1D:27:39 eth0.1 00:15:6D:1D:27:39 eth0.2 00:15:6D:1D:27:39 wlan0 00:15:6D:1C:27:39 wlan0-1 00-15-6D-1C-27-39-00-44-00-00-00-00-00-00-00-00 /proc/cpuinfo system type : Atheros AR7240 rev 2 machine : Ubiquiti Bullet M processor : 0 cpu model : MIPS 24Kc V7.4 BogoMIPS : 259.27 wait instruction : yes microsecond timers : yes tlb_entries : 16 extra interrupt vector : yes hardware watchpoint : yes, count: 4, address/irw mask: [0x0000, 0x0ff8, 0x0ff8, 0x0ff8] isa : mips1 mips2 mips32r1 mips32r2 ASEs implemented : mips16 shadow register sets : 1 kscratch registers : 0 core : 0 VCED exceptions : not available VCEI exceptions : not available nvram hsmmmesh.settings=settings hsmmmesh.settings.wifimac=00:15:6d:1c:27:39 hsmmmesh.settings.mac2=28.39.57 hsmmmesh.settings.dtdmac=29.39.57 hsmmmesh.settings.node=W6ABJ-NB5-Q-1 hsmmmesh.settings.config=mesh
Part of the AREDN™ Project. For more details please see here
1205 '0xe2b5' => { SHOULD BE '0xe235' <--------------------------------
1206 'name' => 'NanoBridge M5',
1207 'comment' => 'NanoBridge M5',
1208 'supported' => '1',
1209 'maxpower' => '22',
1210 'pwroffset' => '1',
1211 'usechains' => 1,
1212 'rfband' => '5800ubntus',
1142 '0xe232' => {
1143 'name' => 'NanoBridge M2',
1144 'comment' => 'NanoBridge M2',
1145 'supported' => '1',
1146 'maxpower' => '21',
1147 'pwroffset' => '2',
1148 'usechains' => 1,
1149 'rfband' => '2400',
1150 },
1151 '0xe239' => {
1152 'name' => 'NanoBridge M9',
1153 'comment' => 'NanoBridge M9',
1154 'supported' => '1',
1155 'maxpower' => '22',
1156 'pwroffset' => '6',
1157 'usechains' => 1,
1158 'rfband' => '900',
This line should not be 0xe235.
Ubiquiti makes periodic adjustments to its hardware line and changes the boardID. As the page says the devices is unsupported (and is unknown) and needs to go through testing routines and verify the data of the hardware for proper operation. I'm guessing you had this device for a while or it was a 2nd hand purchase? Being a 0xe235 I suspect its an older run then 0xe2b5 and as such we havne't seen it.
Before this can be started we need a copy of the board.info file. To obtain this install AirOS on the device and then:
1) Set your PC's ip to 192.168.1.2 / 255.255.255.0
2) Telnet/SSH/Putty into the Nanostation (default user is ubnt; password ubnt; default ip 192.168.1.20)
3) Run "cat /etc/board.info
4) Save the results and post it in response to this post.
PS: After you save and reboot one time you *SHOULD* get the extra ham only channels should show up as a frequency as the hardware is reanalyzed.
board.sysid=0xe235
board.cpurevision=0x000000c2
board.name=NanoBridge M5
board.shortname=NB5
board.subtype=
board.netmodes=7;
board.hwaddr=00156D1EED1F
board.reboot=30
board.upgrade=150
board.phycount=1
board.phy.1.maxmtu=1524
board.phy.2.maxmtu=1524
radio.1.name=
radio.1.shortname=
radio.1.bus=pci
radio.1.subsystemid=0xe235
radio.1.subvendorid=0x0777
radio.1.txpower.max=23
radio.1.txpower.offset=1
radio.1.antennas=3
radio.1.def_antenna=4
radio.1.antenna.1.id=4
radio.1.antenna.1.name=Not specified
radio.1.antenna.1.gain=0
radio.1.antenna.2.id=1
radio.1.antenna.2.name=300
radio.1.antenna.2.gain=22
radio.1.antenna.3.id=2
radio.1.antenna.3.name=400
radio.1.antenna.3.gain=25
This has missed the cutoff to be in 3.16.1.0 and the next window of opportunity is the next beta release (timing not yet determined). Please report the results of any testing on 0xe235.