Hi,
Recently I tuned this device to channel -2 (Frequency 2397). It worked and I was able to join the mesh. So I'm just wondering if there's any downside of this or anybody tried this before?
Recently I tuned this device to channel -2 (Frequency 2397). It worked and I was able to join the mesh. So I'm just wondering if there's any downside of this or anybody tried this before?
1) using telnet or ssh, login to the device with user = ubnt and password = ubnt at IP address 192.168.1.20 .
2) "cat /etc/board.info" file and copy-paste and post back here.
3) "dmesg" and copy-paste output back here.
Joe AE6XE
This might also open the possibility for the device to transmit out-of-band. 900 MHz is only 25 MHz wide in the US--that's 5 channels of 5 MHz each and technically only 1 entirely in band at 20 MHz bandwidth. I can't vouch for other countries. Please use caution when you see the Unsupported Device banner.
Andre, K6AH
I know it's like 9 years ago this post was. But I got 2 NanoStation Loco M900 between my hands now. I did what you asking for and I past it here.
NanoStation Loco M900
sh: /usr/bin/X11/xauth: not found
BusyBox v1.11.2 (2014-01-23 16:56:38 EET) built-in shell (ash)
Enter 'help' for a list of built-in commands.
XM.v5.5.8# cat /etc/board.info
board.sysid=0xe009
board.cpurevision=0x000000c2
board.name=NanoStation Loco M900
board.shortname=N9N
board.subtype=
board.netmodes=7
board.hwaddr=00156D9C1809
board.reboot=30
board.upgrade=150
board.phycount=1
board.phy.1.maxmtu=1524
board.phy.2.maxmtu=1524
radio.1.name=
radio.1.shortname=
radio.1.bus=pci
radio.1.subsystemid=0xe009
radio.1.subvendorid=0x0777
radio.1.txpower.max=28
radio.1.txpower.offset=6
radio.1.antennas=3
radio.1.def_antenna=4
radio.1.antenna.1.id=4
radio.1.antenna.1.name=Internal
radio.1.antenna.1.gain=8
radio.1.antenna.2.id=5
radio.1.antenna.2.name=External
radio.1.antenna.2.gain=0
radio.1.antenna.3.id=6
radio.1.antenna.3.name=External + Internal
radio.1.antenna.3.gain=0
XM.v5.5.8#
XM.v5.5.8# dmesg
[ 0.000000] Linux version 2.6.32.54 (buildd@builder) (gcc version 4.1.2) #1 Thu Jan 23 17:01:23 EET 2014
[ 0.000000] flash_size passed from bootloader = 0
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00002000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00002000
[ 0.000000] On node 0 totalpages: 8192
[ 0.000000] free_area_init_node: node 0, pgdat 802c50d0, node_mem_map 81000000
[ 0.000000] Normal zone: 64 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 8128 pages, LIFO batch:0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: console=ttyS0,115200 root=31:03 rootfstype=squashfs init=/init mtdparts=ar7240-nor0:256k(u-boot),64k(u-boot-env),1024k(kernel),6528k(rootfs),256k(cfg),64k(EEPROM)
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 29388k/32768k available (2290k kernel code, 3380k reserved, 539k data, 136k init, 0k highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:128
[ 0.000000] plat_time_init: plat time init done
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] Calibrating delay loop... 259.58 BogoMIPS (lpj=129792)
[ 0.016000] Mount-cache hash table entries: 512
[ 0.019000] NET: Registered protocol family 16
[ 0.021000] ===== ar7240_platform_init: 0
[ 0.021000] PCIe WLAN H/W found [tries: 1]
[ 0.021000] PCI init:ar7240_pcibios_init
[ 0.021000] ar7240_pcibios_init(368): PCI CMD write: 0x356
[ 0.021000] registering PCI controller with io_map_base unset
[ 0.030000] bio: create slab <bio-0> at 0
[ 0.031000] usbcore: registered new interface driver usbfs
[ 0.032000] usbcore: registered new interface driver hub
[ 0.032000] usbcore: registered new device driver usb
[ 0.033000] pci 0000:00:00.0: reg 10 64bit mmio: [0x000000-0x00ffff]
[ 0.033000] pci 0000:00:00.0: supports D1
[ 0.033000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.033000] pci 0000:00:00.0: PME# disabled
[ 0.034000] Returning IRQ 48
[ 0.035000] Switching to clocksource MIPS
[ 0.038000] NET: Registered protocol family 2
[ 0.038000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.040000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.040000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.040000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.040000] TCP reno registered
[ 0.041000] NET: Registered protocol family 1
[ 0.041000] AR7240 GPIOC major 0
[ 0.043000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.043000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.043000] msgmni has been set to 57
[ 0.044000] io scheduler noop registered (default)
[ 0.071000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.073000] serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
[ 0.374000] console [ttyS0] enabled
[ 0.379000] 6 cmdlinepart partitions found on MTD device ar7240-nor0
[ 0.385000] Creating 6 MTD partitions on "ar7240-nor0":
[ 0.391000] 0x000000000000-0x000000040000 : "u-boot"
[ 0.397000] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.404000] 0x000000050000-0x000000150000 : "kernel"
[ 0.410000] 0x000000150000-0x0000007b0000 : "rootfs"
[ 0.416000] mtd: partition "rootfs" set to be root filesystem
[ 0.422000] 0x0000007b0000-0x0000007f0000 : "cfg"
[ 0.428000] 0x0000007f0000-0x000000800000 : "EEPROM"
[ 0.435000] usbmon: debugfs is not available
[ 0.439000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.446000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.453000] u32 classifier
[ 0.456000] Performance counters on
[ 0.460000] input device check on
[ 0.463000] Actions configured
[ 0.469000] TCP westwood registered
[ 0.473000] NET: Registered protocol family 10
[ 0.482000] NET: Registered protocol family 17
[ 0.486000] Bridge firewalling registered
[ 0.490000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 0.497000] All bugs added by David S. Miller <davem@redhat.com>
[ 0.503000] ar7240wdt_init: Registering WDT success
[ 0.519000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 0.527000] Freeing unused kernel memory: 136k freed
[ 0.547000] Please be patient, while AirOS loads ...
[ 1.705000] Algorithmics/MIPS FPU Emulator v1.5
[ 6.996000] AG7240: Length per segment 1536
[ 6.996000] AG7240: skb_overhead 64, shinfo: 344
[ 6.996000] AG7240: RX sizes - 2k_fit: 1614, reserve: 0
[ 6.996000] AG7240: Max segments per packet 1
[ 6.996000] AG7240: Max tx descriptor count 80
[ 6.996000] AG7240: Max rx descriptor count 252
[ 6.996000] AG7240: fifo cfg 3 01f00140
[ 6.996000] AG7240CHH: Mac address for unit 0
[ 6.996000] AG7240CHH: 00:15:6d:9d:18:09
[ 7.203000] AG7240CHH: Mac address for unit 1
[ 7.203000] AG7240CHH: 02:15:6d:9d:18:09
[ 7.444000] ar7240-gpio 1.1 initialised
[ 7.798000] SCSI subsystem initialized
[ 8.555000] PPP generic driver version 2.4.2
[ 8.719000] PPP MPPE Compression module registered
[ 8.753000] NET: Registered protocol family 24
[ 9.553000] ath_hal: module license 'Proprietary' taints kernel.
[ 9.553000] Disabling lock debugging due to kernel taint
[ 9.981000] ath_hal: 0.9.17.1 (AR5416, DEBUG, REGOPS_FUNC, 11D)
[ 10.470000] wlan: 0.8.4.2 (Atheros/multi-bss)
[ 10.536000] wlan: mac acl policy registered
[ 10.636000] wlan_me: Version 0.1
[ 10.636000] Copyright (c) 2008 Atheros Communications, Inc. All Rights Reserved
[ 10.759000] usbcore: registered new interface driver cdc_acm
[ 10.759000] cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
[ 10.975000] usbcore: registered new interface driver usbserial
[ 10.976000] USB Serial support registered for generic
[ 10.976000] usbcore: registered new interface driver usbserial_generic
[ 10.976000] usbserial: USB Serial Driver core
[ 11.087000] Initializing USB Mass Storage driver...
[ 11.087000] usbcore: registered new interface driver usb-storage
[ 11.087000] USB Mass Storage support registered.
[ 11.177000] USB Serial support registered for GSM modem (1-port)
[ 11.178000] usbcore: registered new interface driver option
[ 11.178000] option: v0.7.2:USB Driver for GSM modems
[ 11.289000] USB Serial support registered for Sierra USB modem
[ 11.290000] usbcore: registered new interface driver sierra
[ 11.290000] sierra: v.1.3.8:USB Driver for Sierra Wireless USB modems
[ 11.495000] fuse init (API version 7.13)
[ 11.866000] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
[ 13.082000] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
[ 13.723000] ath_pci: 0.9.4.5 (Atheros/multi-bss)
[ 13.723000] PCI: Setting latency timer of device 0000:00:00.0 to 64
[ 13.728000] ar5416Attach: Mac Chip.Rev 0x80.2 PCI devid 0xff1c
[ 13.732000] ath_hal: Ubiquiti M900
[ 13.732000] ath_hal: NF adjust values: 5G - 0/0/0/0/0/0, 2G: -110/0/0/-110/0/0
[ 13.746000] wifi0: Atheros 928x: mem=0x10000000, irq=48 hw_base=0xb0000000
[ 14.608000] ubnt_poll: Initializing polling module...
[ 14.608000] ubnt_poll: Initializing packet classifier...
[ 14.609000] ubnt_poll: OS timer frequency 1000 Hz
[ 14.679000] rssi-leds 1.2 loaded
[ 14.766000] ubnt_poll: Attaching hooks...
[ 14.833000] ubnt_poll: TX CTRL configured with 0/18/200/0/6/0/0
[ 14.833000] ubnt_poll: Initializing STA ranging engine
[ 14.833000] ubnt_poll: Setting timing params to min:1000 max:3000 offset:3000 tx_time: 3000 init: 5
[ 14.833000] ubnt_poll: Setting aggregation params to non-txop:0 tx-op:0 scheduling:0
[ 14.833000] ubnt_poll: Setting TXOP Window parameters to size:25 timeout-perc:5
[ 14.833000] ubnt_poll: AR7240 CPU Freq set at 390 MHz, using auxillary timer at 40 KHz
[ 14.833000] ubnt_poll: Module started in STA mode
[ 15.565000] Ebtables v2.0 registered
[ 16.035000] device eth0 entered promiscuous mode
[ 16.041000] device ath0 entered promiscuous mode
[ 16.047000] device eth1 entered promiscuous mode
[ 16.078000] ag7240_ring_alloc Allocated 1920 at 0x80e6c000
[ 16.078000] ag7240_ring_alloc Allocated 6048 at 0x80eea000
[ 16.080000] Setting PHY...
[ 19.117000] AG7240: enet unit:0 phy:4 is up...GMii 100Mbps full duplex
[ 19.117000] AG7240: done cfg2 0x7135 ifctl 0x10000 miictrl
[ 19.117000] AG7240: enet unit 0 phy 4 mode 0x4c04
[ 19.164000] device wifi0 entered promiscuous mode
[ 19.178000] ADDRCONF(NETDEV_UP): ath0: link is not ready
[ 19.185000] ADDRCONF(NETDEV_UP): ath0: link is not ready
[ 19.191000] br0: port 1(eth0) entering learning state
[ 19.326000] ag7240_ring_alloc Allocated 1920 at 0x80f48000
[ 19.326000] ag7240_ring_alloc Allocated 6048 at 0x80f50000
[ 19.328000] ATHRS26: resetting s26
[ 19.443000] ATHRS26: s26 reset done
[ 19.446000] Setting PHY...
[ 20.191000] br0: port 1(eth0) entering forwarding state
[ 20.531000] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 20.538000] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 29.689000] eth0: no IPv6 routers present
[ 29.734000] br0: no IPv6 routers present
XM.v5.5.8#
73
Sebastien VE2ZL/VE2GTZ